Requirements for alcohol management equipment installed without internet

5 min read

Even at construction sites without internet coverage, underground work areas, or facilities where external network connections are restricted, you may need to check whether workers have been drinking before work. Here, alcohol management equipment can mean not only a device that measures breath and displays a result, but also the setup that identifies the person tested and stores results or transfers them to the office.

The lack of internet does not mean testing is impossible. However, checking results at the site, keeping results for each person, and gathering results at the office later are different requirements. When choosing equipment to install, start by deciding how far through these four steps the site itself needs to go, rather than focusing on whether there is a connection.

Decide which work must be finished at the site after testing

At some sites, it is enough to be able to tell from the screen whether a test is complete or has an error. By contrast, sites that need to record who tested and when, such as pre-shift tests, must consider identifying the tester and whether results are stored in the device, in addition to displaying results. Both cases may involve offline testing, but the equipment setup needed is not the same.

If testers need to be identified, decide whether to load a site roster into the device in advance, have people select a name or number at the site, or check results only without a separate identification step. If you plan to use the equipment with other systems such as cameras or doors, the requirements must also state what information needs to pass between devices even without internet.

Turn the reason there is no connection into installation conditions

"No internet" covers a mix of situations: no wired line, a weak mobile signal, restrictions on wireless communication, or no possibility of connecting to an external network at all. These differ in what peripheral equipment can be brought to the site and how results can be transferred, so they cannot be treated as the same condition.

For example, if the office computer can be used but the work area has no internet, the key is the process of moving results measured at the site to the office. Conversely, at a facility where even external communication devices cannot be brought in, you must not assume phone connectivity as a temporary fallback. If you first set out the connection methods the facility allows and the restrictions on what can be brought in, and pass them to the supplier, you can sort out which setups are possible and which are not before getting a quote.

Put the results you need in the quote, not feature names

The items below do not refer to the features of a specific product. They are criteria for conveying the site's goals to the supplier and setting out the scenes to check in a demonstration.

Work needed at the site Criteria to set when there is no internet Scene to check in the demonstration
Checking breath test results Tell at the site whether a test is complete, has an error, or needs a retest Check the test screen with communication turned off
Identifying testers Decide whether to use a roster and which identification methods to allow Check how cases with no roster or an outdated roster are handled
Storing results Decide how much information to keep in the device Check that earlier results can be viewed after restarting the power
Delivering to the office Decide how results will be moved and how to check for gaps and duplicates Check the result transfer process at a location where a connection is available

Result storage is hard to judge from a description that just says "can record." The storage scope differs depending on whether you need only the reading or also the test time and tester information. You also need confirmation, based on that equipment and setup, of how existing results and new tests are handled when the storage is full.

Look separately at having no connection from the start and losing it midway

A demonstration run while online is not enough to show that offline requirements are met. Behavior can differ between a case where there is no connection from the moment the device is first turned on and a case where the connection drops during use. If the setup needs to receive a user roster or settings at first, testing itself may be possible but the way testers are identified may change.

As a hypothetical example, consider a workplace that wants to run pre-shift tests in an underground work area cut off from external networks and gather the results at the office. First observe whether test results appear on the screen without internet, whether results can still be viewed after the device is restarted, and whether results are transferred completely after connecting at the office. If testing works but testers cannot be identified, it can be interpreted that the setup does not fit a purpose that requires managing results by person.

In that case, you could narrow the scope so the site only checks results, or confirm in a demonstration whether the setup supports the necessary identification and transfer steps without internet. The completion criterion is that the predefined test, identification, storage, and transfer items are reproduced as expected both when there is no connection and when results are being transferred. You can consider preparing the test roster with fictitious names and numbers instead of real employee information.

Compare the components needed besides the main unit

In an offline environment, it is hard to make a purchasing decision by comparing only the main unit. You also need to compare whether the consumables used for testing are compatible with that model, how many to prepare for the expected number of tests, and whether a computer or separate installation work is needed to check or transfer results. The more a setup gathers results by person, the more the initial setup and the scope of on-site usage guidance can vary.

Writing down for each candidate what is done at the site and what is done at the office makes it easier to spot setups that are excessive or inadequate. Before installation, you can consider making testing with communication cut off, checking results after a power restart, and the process of moving results to the office part of the acceptance items. Confirming in this process that the results you need are reproduced turns the equipment requirements for a place without internet into concrete purchasing conditions.

References

#offline operation
#alcohol management system
#network requirements
Considering our products?
We'll help you decide.