A breathalyzer is equipment that analyzes a breath sample and displays a result, used for workplace checks and safety management at agencies. If it will not power on, no test can be done, so the person in charge of the equipment should first remove that device from testing work, separately from its calibration cycle. The purpose of checks before after-sales service is not to find and fix the cause of the fault yourself, but to distinguish the power response and external condition within the scope the manufacturer specifies and pass that on.
A state in which nothing appears when the power button is pressed, a state in which the start screen appears briefly and then shuts off, and a state in which a message is displayed but nothing proceeds all need to be recorded differently. Batteries and charging components are the accessories that supply electricity to the equipment, and how they are used and what they are compatible with can differ by model. So connecting similar-looking parts meant for other equipment, or opening the unit to work on the contacts, is not part of the checks before after-sales service.
Record the response on screen as it actually was
Write down briefly and specifically what you saw when you pressed the power button. For example, write "neither the screen nor the indicator light comes on when the button is pressed," "the start screen appears and then shuts off right away," or "after a certain guidance message is displayed, it does not move to the next screen." "Battery failure" or "internal circuit defect" are guesses before inspection, so it is best to keep them separate from what you observed.
Also note when the symptom first appeared and the situation just before it. Record facts you confirmed, such as whether you were trying to use it for the first time after long-term storage, whether it was knocked during transport, and whether there was leakage, deformation, or a smell around the battery. Even if it would not power on after being dropped, do not conclude that the drop was the cause. Just pass it on as part of the sequence of events.
Compare only against the power configuration in the manual
Compare the batteries, charging cable, charging cradle, and so on with the configuration given in the user manual for the current model. The basic scope of checks is looking at whether things are inserted in the right direction, whether connected parts are loose, and whether there are visible cracks or dirt on the unit and power items. Even a charger or battery that worked in another device cannot be assumed to be the right configuration for the current breathalyzer.
If you see battery leakage, swelling, a burning smell, severe cracks, or signs of water damage, it is best not to keep trying to turn on the power. Also avoid touching connections with wet hands, or pressing or bending contacts with metal tools. In these cases, separating and storing the equipment and keeping its condition as needed for the after-sales service request takes priority over trying to restore power.
| What to check | What to pass on to after-sales service | Actions beyond the scope of checks |
|---|---|---|
| Equipment information | Model name, serial number, power configuration used | Removing labels or opening the unit to find internal information |
| Power response | No display, briefly lights up then shuts off, on-screen message | Operating it repeatedly to keep reproducing the symptom |
| External condition | Whether there are cracks, leakage, smell, or signs of water damage | Disassembling it to clean contacts or remove parts |
| Sequence of events | When it first occurred and the situation just before storage, transport, or use | Concluding from observation alone that a particular part is the cause |
Splitting the items as in the table reduces information missed on the phone or in a request form. In particular, rather than just writing "I charged it," it helps the after-sales service decision to write that you checked the power preparation method given in the manual and which components you actually used. If you performed the permitted checks several times, also record the order in which you did them and the response each time.
In a hypothetical case, putting it on hold comes first
As a hypothetical case, suppose that when a breathalyzer is taken out of long-term storage, neither the screen nor the indicator light comes on at all when the power button is pressed. The person in charge first looks for cracks, leakage, or smells on the unit and the installed power items, and compares the power preparation method in that model's manual with the current components. The interpretation at this point stays at the level of "no display on the screen or indicator light even after the specified power preparation," not "internal fault."
A possible action goes only as far as checking the installation state and power configuration permitted by the manual. If nothing changes, remove the device from testing work and pass on the model name, serial number, power response, and the items checked to after-sales service. The completion criterion in this case is not turning the equipment back on by improvised means, but a state in which you have determined whether there are any safety warning signs and have gathered all the observations needed for the request.
Organize the request using materials for the right model
DATECH's official Downloads section posts product manuals and materials related to calibration and repair requests. However, you must first check that the model name on the material matches the model name of the actual equipment. A manual for another model with a similar appearance, or a teardown video online, may not explain the current equipment's power configuration and screen displays.
Include in the after-sales service request the model name and serial number, the power response observed, the power configuration used, when the symptom occurred, and the checks actually performed within the scope of the manual. Photos of on-screen messages or the external condition may be needed, but there is no need to force the equipment to operate to create them. Decide whether to send power-related accessories with it according to the request guidance, and keep a list of the items actually enclosed to compare when it is returned.
Manage repair and calibration separately
Even if the power comes back on, that does not erase the fact that there was a power problem. Keep a record in the equipment management log if it repeatedly shut off or the power supply was unstable, and organize separately the condition of the equipment returned after repair and the guidance provided. Repair is the procedure of inspecting and restoring a malfunction, while calibration is the procedure of confirming the accuracy of readings, so it is best not to combine them into a single completed item.
If testing work must continue, you can check the readiness of replacement equipment to use while the faulty equipment is being handled. On the other hand, for equipment that had a power problem, rather than continuing with improvised tests, it is appropriate to decide whether to resume use after receiving the after-sales inspection results and the manufacturer's guidance. This way, you can keep both the information needed for the repair request and the equipment management history without going beyond the scope of checks.